True 18oz Gunmetal Shaker
Location: (chicago)
The True 18oz Gunmetal Shaker is a stainless steel cocktail shaker with an 18-ounce capacity for mixing beverages. Its gunmetal finish gives the exterior a dark metallic appearance, while the fitted cap and built-in strainer support shaking and pouring from one vessel. The shaker is used by adding ingredients, securing the cap, and shaking the contents before pouring. It also includes a jigger cap for measuring. This barware piece is suited to cocktail preparation in bars, restaurants, and beverage service areas.
If you're looking for True 18oz Gunmetal Shaker, they are an excellent choice for the smooth operation of your bar & restaurant.
Visit: https://www.bistrotorestro.com/18oz-gunmetal-shaker-by-true-842094105014
True 18oz shaker, gunmetal cocktail shaker, stainless steel shaker, True barware, 18 ounce shaker, cocktail mixing shaker, bar beverage equipment, cocktail preparation
Website
Email
8669630907 
The General Electric WR14X29858 Refrigerator Freezer Door Gasket helps create a proper seal around the freezer door, supporting consistent cooling conditions inside the compartment. Made to fit around the door opening, this white gasket compresse...
The Robot Coupe 27265 Dicing Kit is a cutting accessory configured to produce 10 x 10 mm dice with compatible R2 food processors. The kit works with the processor’s cutting mechanism to divide prepared food into uniform square pieces during ope...
The General Electric WR55X30121 Control Display provides the front interface used to operate and monitor compatible refrigerator functions. This stainless steel control display assembly houses the operating controls and display elements that allo...
The Prince Castle 86-168-3A6 Drain Shelf is a 1/3-size component designed for compatible commercial foodservice equipment. Its shelf-style configuration provides a designated surface for draining and holding food products during preparation or servic...
The Southbend 1182762 is a sectional charbroiler burner assembly designed for compatible commercial cooking equipment. The burner assembly forms part of the charbroiler heating system and provides the heat source required for cooking operations. Its ...
The General Electric WR71X38288 Refrigerator Full Door Shelf provides organized storage space along the refrigerator door for bottles, containers, and other items. Designed to fit into the door’s designated shelf position, this part attache...
The Henny Penny 17407 Connector 1/2" MPT Male Elbow is a 90-degree threaded fitting used in compatible fryer plumbing and filter-pump assemblies. Its angled configuration changes the direction of a connected line while providing a threaded conne...
The Vollrath/Idea-Medalie XCBL9001 Burner Cover is a replacement component used to cover and protect the burner area in compatible commercial foodservice equipment. Positioned over the designated burner assembly, the cover helps provide a defined sur...
The Delfield 3234226 Refrigerator Hinge Bracket TL/BR is a mounting component used in commercial refrigeration equipment. The bracket supports the hinge assembly at the designated top-left or bottom-right position of the refrigerator. Its TL/BR desig...
The General Electric WD22X33499 Dishwasher Lower Spray Arm Assembly distributes water across the lower section of the dishwasher tub during wash cycles. Positioned beneath the lower dish rack, this rotating arm connects to the dishwasher’s ...
The Groen Z001524 Bulb Only Clear 250V is a replacement lighting component used within commercial foodservice equipment where a clear bulb is specified. Its electrical rating should be matched with the equipment requirements before installation, whil...
The Avanti Products Z-G20A23-030102 Range Electric Surface Unit Knob provides a manual interface for operating the range’s electric surface unit. Installed on the control shaft, the knob connects with the corresponding switch and allows use...
The Cecilware F177A Fryer Brass Orifice 52 is a brass gas orifice used in commercial fryer burner assemblies. The No. 52 opening controls the amount of gas passing through the burner system according to the specified configuration. Its brass construc...
The Garland 4523902 Range Briquettes are listed as an 84-piece set for Garland gas range and broiler assemblies. Installed within the cooking area, these briquettes sit in the broiler section and form part of the heat distribution arrangement above t...
The Groen Z005612 hex head cap screw is a 3/8-16 x 1 inch fastener used with compatible commercial foodservice equipment. Its hex head design allows standard tools to be used for installation and removal during equipment service. This replacement scr...
The Star Mfg 2N-Y3084 Charbroiler Heating Element Bent 1650W 208V is a bent heating element listed for Star charbroilers. Its 208V rating and 1650W specification identify operating requirements for equipment service and part verification. When sour...
The LG EBR74045822 Air Conditioner Main PCB Assembly manages electrical signals and coordinates essential air conditioner operations. This main printed circuit board receives input from connected controls and sensors, then directs electrical comm...
The Garland 4518241 Oven Burner Hanger is a support component used within compatible commercial cooking equipment. Positioned as part of the burner mounting arrangement, the hanger provides a connection point for holding the burner assembly in its i...
The Garland 2117000 Oven Rack is a commercial oven rack measuring 20.5 inches front to back and 26.06 inches left to right. Its dimensions provide a clear reference for oven configurations that use this specific rack size. The rack serves as a suppor...
The Whirlpool W11416788 Dishwasher Front Door Panel provides the exterior section of the dishwasher door and helps protect the internal door elements. Designed to fit on the front of the appliance, this panel attaches to the door structure and fo...